-
XRD of Cuttings of the KTB Pilot Hole HB1d
The qualitative and quantitative phase analyses were performed in the KTB field laboratory by x-ray powder diffraction using SIEMENS D 500 diffractometer. During early stages of... -
Magnetic Susceptibility of Cuttings of the KTB Pilot Hole HB1i
The magnetic susceptibility is measured by an inductive AC device (BARTINGTON). The sample is placed inside a coil which generates an alternating magnetic field. The applied... -
XRF of Cores of the KTB Main Hole HB1d.
Cuttings were crushed in a tungsten carbide ball mill for 25 min; while core samples were crushed in a tungsten carbide jaw breaker and then processed in the same way as the... -
Porosity of Mini Cores (Plugs) of the KTB Main Hole HB1a
The porosity was determined using the most common Archimedian method (Schopper, 1982). It is based on the following three weight determinations of the sample: (1) The samples... -
Axial Vp on Core Samples of the KTB Pilot Hole VB1
Ultrasonic wave propagation through core samples is studied in a water tank to insure good signal transmission between transducer, rock specimen and receiver and to avoid time -... -
Density of Core Samples of the KTB Main Hole HB1i
The density of rocks depends on the mineral contents and is therefore a helpful property for the discrimination of lithological units. It is also used for the calculation of... -
XRF of Cores of the KTB Main Hole HB1a.
Cuttings were crushed in a tungsten carbide ball mill for 25 min; while core samples were crushed in a tungsten carbide jaw breaker and then processed in the same way as the... -
Gas Radon Measurements of Gas Samples of the KTB Main Hole HB1i
In the complete KTB-VB and in in the KTB-HB down to a depth of 3003 m the gas phase was released and collected by twirl degassers attached in front of the mud shakers. This open... -
Natural Gamma-ray Activity of Cuttings of the KTB Main Hole HB1g (measuremen...
In the laboratory, the gamma radiation is measured by a sodium iodtite (NaI) scintillation detector (cores and cuttings) and by a germanium (Ge) semiconductor detector... -
Magnetic Susceptibility of Mini-Cores of the KTB Main Hole HB1d
The magnetic susceptibility is measured by an inductive AC device (BARTINGTON). The sample is placed inside a coil which generates an alternating magnetic field. The applied... -
Gas Mass Spectrometry of Gas Samples of the KTB Main Hole HB1g
In the complete KTB-VB and in in the KTB-HB down to a depth of 3003 m the gas phase was released and collected by twirl degassers attached in front of the mud shakers. This open... -
Natural Gamma-ray Activity of Cuttings of the KTB Main Hole HB1 (measurements...
In the laboratory, the gamma radiation is measured by a sodium iodtite (NaI) scintillation detector (cores and cuttings) and by a germanium (Ge) semiconductor detector... -
Density of Cuttings of the KTB Main Hole HB1g
The density of rocks depends on the mineral contents and is therefore a helpful property for the discrimination of lithological units. It is also used for the calculation of... -
Porosity of Mini Cores (Plugs) of the KTB Main Hole HB1
The porosity was determined using the most common Archimedian method (Schopper, 1982). It is based on the following three weight determinations of the sample: (1) The samples... -
Thermal Conductivity of Cores of the KTB Pilot Hole VB1 (measured data)
The thermal conductivity on cores is measured in two steps (see Pribnow 1994). First, one face end of the core is sawed and polished. The half space line source is pressed... -
Magnetic Susceptibility of Cuttings of the KTB Pilot Hole VB1
The magnetic susceptibility is measured by an inductive AC device (BARTINGTON). The sample is placed inside a coil which generates an alternating magnetic field. The applied... -
XRF of Cuttings of the KTB Main Hole HB1.
Cuttings were crushed in a tungsten carbide ball mill for 25 min; while core samples were crushed in a tungsten carbide jaw breaker and then processed in the same way as the... -
Density of Cuttings of the KTB Main Hole HB1a
The density of rocks depends on the mineral contents and is therefore a helpful property for the discrimination of lithological units. It is also used for the calculation of... -
Thermal Conductivity of Cuttings of the KTB Main Hole HB1 (measured data)
In the KTB field laboratory, thermal conductivity was measured on cuttings material in depth intervals of 10 m and on available drill core material. The results on drill cores... -
XRD of Cores of the KTB Main Hole HB1a
The qualitative and quantitative phase analyses were performed in the KTB field laboratory by x-ray powder diffraction using SIEMENS D 500 diffractometer. During early stages of...
