-
Gas Mass Spectrometry of Gas Samples of the KTB Pilot Hole VB1b
In the complete KTB-VB and in in the KTB-HB down to a depth of 3003 m the gas phase was released and collected by twirl degassers attached in front of the mud shakers. This open... -
Gas Mass Spectrometry of Gas Samples of the KTB Main Hole HB1
In the complete KTB-VB and in in the KTB-HB down to a depth of 3003 m the gas phase was released and collected by twirl degassers attached in front of the mud shakers. This open... -
Axial Vp on Core Samples of the KTB Pilot Hole VB1a
Ultrasonic wave propagation through core samples is studied in a water tank to insure good signal transmission between transducer, rock specimen and receiver and to avoid time -... -
Thermal Conductivity of Cores of the KTB Main Hole HB1 (measured data)
The thermal conductivity on cores is measured in two steps (see Pribnow 1994). First, one face end of the core is sawed and polished. The half space line source is pressed... -
XRF of Centrifuge Samples of the KTB Pilot Hole VB1b.
Cuttings were crushed in a tungsten carbide ball mill for 25 min; while core samples were crushed in a tungsten carbide jaw breaker and then processed in the same way as the... -
XRD of Cuttings of the KTB Main Hole HB1i
The qualitative and quantitative phase analyses were performed in the KTB field laboratory by x-ray powder diffraction using SIEMENS D 500 diffractometer. During early stages of... -
Porosity of Mini Cores (Plugs) of the KTB Main Hole HB1g
The porosity was determined using the most common Archimedian method (Schopper, 1982). It is based on the following three weight determinations of the sample: (1) The samples... -
Gas chromatography of gas samples of the KTB main hole HB1h
The main objective of this drilling fluid analysis was the detection of inflows of formation fluids. Therefore different gases dissolved in the drilling mud were measured... -
Density of Cuttings of the KTB Main Hole HB1h
The density of rocks depends on the mineral contents and is therefore a helpful property for the discrimination of lithological units. It is also used for the calculation of... -
XRD of Cores of the KTB Main Hole HB1i
The qualitative and quantitative phase analyses were performed in the KTB field laboratory by x-ray powder diffraction using SIEMENS D 500 diffractometer. During early stages of... -
Natural Remanent Magnetisation of Cores of the KTB Main Hole HB1g
Natural Remanent Magnetisation of Cores of the KTB Main Hole HB1g -
Natural Gamma-ray Activity of Cores of the KTB Main Hole HB1a
In the laboratory, the gamma radiation is measured by a sodium iodtite (NaI) scintillation detector (cores and cuttings) and by a germanium (Ge) semiconductor detector... -
Axial Vp on Core Samples of the KTB Main Hole HB1
Ultrasonic wave propagation through core samples is studied in a water tank to insure good signal transmission between transducer, rock specimen and receiver and to avoid time -... -
XRD of Cuttings of the KTB Pilot Hole HB1
The qualitative and quantitative phase analyses were performed in the KTB field laboratory by x-ray powder diffraction using SIEMENS D 500 diffractometer. During early stages of... -
Porosity of Mini Cores (Plugs) of the KTB Pilot Hole VB1a
The porosity was determined using the most common Archimedian method (Schopper, 1982). It is based on the following three weight determinations of the sample: (1) The samples... -
Magnetic Susceptibility of Cores of the KTB Pilot Hole VB1
The magnetic susceptibility is measured by an inductive AC device (BARTINGTON). The sample is placed inside a coil which generates an alternating magnetic field. The applied... -
Geochemical Analysis of Cations of Mud Samples of the KTB Pilot Hole VB1.
Geochemical Analysis of Cations of Mud Samples of the KTB Pilot Hole VB1. -
Natural Gamma-ray Activity of Cores of the KTB Main Hole HB1
In the laboratory, the gamma radiation is measured by a sodium iodtite (NaI) scintillation detector (cores and cuttings) and by a germanium (Ge) semiconductor detector... -
Thermal Conductivity of Cuttings of the KTB Main Hole HB1h (measured data)
In the KTB field laboratory, thermal conductivity was measured on cuttings material in depth intervals of 10 m and on available drill core material. The results on drill cores... -
Thermal Conductivity of Cuttings of the KTB Main Hole HB1d (measured data)
In the KTB field laboratory, thermal conductivity was measured on cuttings material in depth intervals of 10 m and on available drill core material. The results on drill cores...
