-
Gas Radon Measurements of Gas Samples of the KTB Main Hole HB1h
In the complete KTB-VB and in in the KTB-HB down to a depth of 3003 m the gas phase was released and collected by twirl degassers attached in front of the mud shakers. This open... -
Density of Core Samples of the KTB Pilot Hole VB1
The density of rocks depends on the mineral contents and is therefore a helpful property for the discrimination of lithological units. It is also used for the calculation of... -
Infrared-Spectrometry on Cutting Samples of the KTB Main Hole (Drill Section ...
Infrared-Spectrometry on Cutting Samples of the KTB Main Hole (Drill Section HB1g), 7220-8322 m. -
Thermal Conductivity of Cuttings of the KTB Main Hole HB1g (transformed data)
In the KTB field laboratory, thermal conductivity was measured on cuttings material in depth intervals of 10 m and on available drill core material. The results on drill cores... -
Infrared-Spectrometry on Cutting Samples of the KTB Main Hole (Drill Section ...
Infrared-Spectrometry on Cutting Samples of the KTB Main Hole (Drill Section HB1a), 5596-6760 m. -
Radial Vp on Core Samples of the KTB Main Hole HB1
Ultrasonic wave propagation through core samples is studied in a water tank to insure good signal transmission between transducer, rock specimen and receiver and to avoid time -... -
Electrical Resistivity of Mini Cores (Plugs) of the KTB Main Hole HB1g
In general, four-electrode devices are used to measure the resistivity on original (unprepared) cores and on mini cores drilled from these original cores. The in-phase and the... -
Thermal Conductivity of Cores of the KTB Main Hole HB1g (measured data)
The thermal conductivity on cores is measured in two steps (see Pribnow 1994). First, one face end of the core is sawed and polished. The half space line source is pressed... -
Magnetic Susceptibility of Cuttings of the KTB Pilot Hole HB1g (special samples)
The magnetic susceptibility is measured by an inductive AC device (BARTINGTON). The sample is placed inside a coil which generates an alternating magnetic field. The applied... -
XRF of Cuttings of the KTB Main Hole HB1h.
Cuttings were crushed in a tungsten carbide ball mill for 25 min; while core samples were crushed in a tungsten carbide jaw breaker and then processed in the same way as the... -
Ultrasonic Seismics on Mini Cores (Plugs) of the KTB Main Hole HB1
Ultrasonic wave propagation through core samples is studied in a water tank to insure good signal transmission between transducer, rock specimen and receiver and to avoid time -... -
Electrical Resistivity of Cores of the KTB Main Hole HB1
In general, four-electrode devices are used to measure the resistivity on original (unprepared) cores and on mini cores drilled from these original cores. The in-phase and the... -
Gas Radon Measurements of Gas Samples of the KTB Main Hole HB1g
In the complete KTB-VB and in in the KTB-HB down to a depth of 3003 m the gas phase was released and collected by twirl degassers attached in front of the mud shakers. This open... -
Density of Cuttings of the KTB Main Hole HB1d
The density of rocks depends on the mineral contents and is therefore a helpful property for the discrimination of lithological units. It is also used for the calculation of... -
Gas chromatography of gas samples of the KTB main hole HB1d
The main objective of this drilling fluid analysis was the detection of inflows of formation fluids. Therefore different gases dissolved in the drilling mud were measured... -
Natural Gamma-ray Activity of Cuttings of the KTB Pilot Hole VB1a
In the laboratory, the gamma radiation is measured by a sodium iodtite (NaI) scintillation detector (cores and cuttings) and by a germanium (Ge) semiconductor detector... -
XRF of Cores of the KTB Main Hole KTB-HB1.
Cuttings were crushed in a tungsten carbide ball mill for 25 min; while core samples were crushed in a tungsten carbide jaw breaker and then processed in the same way as the... -
XRD of Cuttings of the KTB Main Hole HB1h
The qualitative and quantitative phase analyses were performed in the KTB field laboratory by x-ray powder diffraction using SIEMENS D 500 diffractometer. During early stages of... -
Magnetic Susceptibility of Mini-Cores of the KTB Main Hole HB1g
The magnetic susceptibility is measured by an inductive AC device (BARTINGTON). The sample is placed inside a coil which generates an alternating magnetic field. The applied... -
Gas Radon Measurements of Gas Samples of the KTB Main Hole HB1d
In the complete KTB-VB and in in the KTB-HB down to a depth of 3003 m the gas phase was released and collected by twirl degassers attached in front of the mud shakers. This open...
