-
The lattice parameter displacements in kamacite and taenite phases in metalli...
The bulk of metal meteorites consists of the Fe,Ni-alloys kamacite [α-(Fe,Ni), bcc structure] and taenite [γ-(Ni,Fe), fcc structure]. The chemical composition is... -
Temperature-Dependent Analysis of Polar Nanostructures in High Temperature Re...
A number of relaxor ferroelectric ceramics possess a near-stable relative permittivity over a wide temperature range, making them promising materials for electronic applications... -
Determining the nanostructure of the active layer in thin film organic photov...
Organic photovoltaics are a low cost alternative to existing photovoltaic materials and their efficiency is steadily increasing towards the point where their cost per Watt is... -
Engin-X Proposal: Measuring Residual Stress in ISIS Targets Using an Asymmetr...
This dataset has no description
-
Residual Stress Measurement of Weld Repaired IN718 by Neutron Diffraction
Repair welds are usually introduced into structures either to remedy initial fabrication defects in castings or welds, or to rectify in-service degradation of components and... -
Continue improving reliability of residual stress characterization in dissimi...
The proposed experiment is the final experimental step for validating the measurement methods and analytical models developed based on the systematic experimental studies... -
IN SITU CHARACTERISATION OF INTERNAL STRESSES IN A CLAD PRESSURE VESSEL STEEL...
Nuclear reactor pressure vessels are safety critical components of pressurised light water reactors. They enclose the nuclear fuel rods, that contain the nuclear fuel (uranium... -
LOW DIMENSIONAL NETWORKS UNDER PRESSURE. IN-SITU DIFFRACTION MEASUREMENTS OF ...
Carbonate liquids are characterised by low temperature and low viscosity and play an important role in molten carbonate fuel cells, battery electrolytes and, surprisingly, in... -
Modelling decarburization in BF-BOF steel making
70% of the worlds steel production is conducted via the blast furnace-basic oxygen furnace (BF-BOF, Fig 1.) route using raw materials to meet the low residual, low inclusion... -
Hysteresis in the deformation of layered crystal structures
The aim of this proposal is to study the origin of the hysteresis effect in many layered crystal structures, in particular MAX-phases, such as Ti2AlC. This effect has been... -
Probing the spatial distribution of fluorophores entering nanoscale pores in ...
We wish to make specular NR measurements on fluorophore functionalization of amine-functionalized polypyrrole (PPy-NH2) films. The critical issue is film penetration of solution... -
Towards reliable residual stress characterization in dissimilar metal welds
The proposed experiment forms a part of a joint study by M. Rahman, an ILL PhD thesis student, and J. Brokx, a CDT thesis student supported by ISIS. In the proposed experiment,... -
Effect of Build Strategies on the Development of Residual Stresses in Laser M...
Laser metal deposition (LMD) is a layer-by-layer additive manufacturing process used to produce near-net shaped components in the aerospace industry, with complex geometries... -
Investigation of the residual strain evolution upon in situ annealing of the ...
The present research proposal focuses on solving technological challenges associated with the implementation of components of Nickel superalloys produced by Additive... -
Residual Stress Evolution in HVOF Thermal Sprayed WC-17Co Coating induced by ...
Due to the existence of complex residual stresses, the High-velocity oxygen-fuel (HVOF) thermal sprayed WC-Co coating, as surface protection in many tribological applications... -
Microstrain evolution of multilayered Ti/X (X=Zr, Nb) composites under the ef...
The mechanical properties of multilayered metallic composites are determined by strain/stress partitioning between the constituent metals. However, the effect of strain on the... -
In-situ Neutron Diffraction Study on the Tension and Creep Behavior of the Al...
Resubmitted proposal. High-entropy alloys (HEAs) are loosely defined as solid solution alloys that contain more than five principal elements in equal or near equal atomic... -
Measuring the strain profile in opposed sapphire anvils
Sapphire can be used as a hard anvil material to generate high pressures on other samples of interest. Sapphire anvils, though not as strong as diamond anvils, are easily... -
MAPS commissioning
This dataset has no description
-
Low field µSR studies of radiation chemistry and free radical reactions by no...
Microwave (MW) assisted chemical reactions are of interest as a green, energy efficient alternative to conventional thermal heating for chemical processes. MW irradiation...
