-
Gas chromatography of gas samples of the KTB pilot hole VB!
The main objective of this drilling fluid analysis was the detection of inflows of formation fluids. Therefore different gases dissolved in the drilling mud were measured... -
Magnetic Susceptibility of Mini-Cores of the KTB Main Hole HB1a
The magnetic susceptibility is measured by an inductive AC device (BARTINGTON). The sample is placed inside a coil which generates an alternating magnetic field. The applied... -
Natural Remanent Magnetisation of Cores of the KTB Main Hole HB1a
Natural Remanent Magnetisation of Cores of the KTB Main Hole HB1a -
Density of Core Samples of the KTB Main Hole HB1a
The density of rocks depends on the mineral contents and is therefore a helpful property for the discrimination of lithological units. It is also used for the calculation of... -
Electrical Resistivity of Mini Cores (Plugs) of the KTB Main Hole HB1
In general, four-electrode devices are used to measure the resistivity on original (unprepared) cores and on mini cores drilled from these original cores. The in-phase and the... -
XRF of Cuttings of the KTB pilot hole VB1
Cuttings were crushed in a tungsten carbide ball mill for 25 min; while core samples were crushed in a tungsten carbide jaw breaker and then processed in the same way as the... -
Magnetic Susceptibility of Cuttings of the KTB Pilot Hole HB1a
The magnetic susceptibility is measured by an inductive AC device (BARTINGTON). The sample is placed inside a coil which generates an alternating magnetic field. The applied... -
Geochemical Analysis of Cations of Mud Samples of the KTB Main Hole HB1h.
Geochemical Analysis of Cations of Mud Samples of the KTB Main Hole HB1h. -
Gas mass spectrometry of gas samples from the KTB Main Hole HB1
The main objective of this drilling fluid analysis was the detection of inflows of formation fluids. Therefore different gases dissolved in the drilling mud were measured... -
XRF of Cuttings of the KTB Main Hole HB1g.
Cuttings were crushed in a tungsten carbide ball mill for 25 min; while core samples were crushed in a tungsten carbide jaw breaker and then processed in the same way as the... -
Permeability of Mini Cores of the KTB Main Hole HB1g
In the KTB field laboratory, porosity, internal surface and permeability were determined on identical mini cores with 25.4 mm in diameter and approximately 50 mm in length.... -
Geochemical Analysis of Cations of Mud Samples of the KTB Main Hole HB1g.
Geochemical Analysis of Cations of Mud Samples of the KTB Main Hole HB1g. -
Magnetic Susceptibility of Cuttings of the KTB Pilot Hole HB1d
The magnetic susceptibility is measured by an inductive AC device (BARTINGTON). The sample is placed inside a coil which generates an alternating magnetic field. The applied... -
Thermal Conductivity of Cuttings of the KTB Main Hole HB1i (transformed data)
In the KTB field laboratory, thermal conductivity was measured on cuttings material in depth intervals of 10 m and on available drill core material. The results on drill cores... -
Density of Core Samples of the KTB Main Hole HB1
The density of rocks depends on the mineral contents and is therefore a helpful property for the discrimination of lithological units. It is also used for the calculation of... -
Natural Gamma-ray Activity of Cuttings of the KTB Main Hole HB1i (measurement...
In the laboratory, the gamma radiation is measured by a sodium iodtite (NaI) scintillation detector (cores and cuttings) and by a germanium (Ge) semiconductor detector... -
XRF of Centrifuge Samples of the KTB Pilot Hole VB1a.
Cuttings were crushed in a tungsten carbide ball mill for 25 min; while core samples were crushed in a tungsten carbide jaw breaker and then processed in the same way as the... -
Permeability of Mini Cores of the KTB Pilot Hole VB1a
In the KTB field laboratory, porosity, internal surface and permeability were determined on identical mini cores with 25.4 mm in diameter and approximately 50 mm in length.... -
XRD of Cuttings of the KTB Pilot Hole VB1a
The qualitative and quantitative phase analyses were performed in the KTB field laboratory by x-ray powder diffraction using SIEMENS D 500 diffractometer. During early stages of... -
Permeability of Mini Cores of the KTB Main Hole HB1d
In the KTB field laboratory, porosity, internal surface and permeability were determined on identical mini cores with 25.4 mm in diameter and approximately 50 mm in length....
