-
Data concerning preparation of pollen concentrates and graphite targets and r...
Laboratory processing of concentrates was aimed at the removal of non-sporomorph organic matter by means of chemical treatment, micro-sieving and heavy liquid seperation. The... -
SAFOD Main Hole downhole logging data phase 1.1
SAFOD is motivated by the need to answer fundamental questions about the physical and chemical processes controlling faulting and earthquake generation within a major... -
Electrical Resistivity of Cores of the KTB Pilot Hole VB1a
In general, four-electrode devices are used to measure the resistivity on original (unprepared) cores and on mini cores drilled from these original cores. The in-phase and the... -
Axial Vp on Core Samples of the KTB Main Hole HB1a
Ultrasonic wave propagation through core samples is studied in a water tank to insure good signal transmission between transducer, rock specimen and receiver and to avoid time -... -
Electrical Resistivity of Cores of the KTB Pilot Hole HB1g
In general, four-electrode devices are used to measure the resistivity on original (unprepared) cores and on mini cores drilled from these original cores. The in-phase and the... -
Thermal Conductivity of Cuttings of the KTB Main Hole HB1d (transformed data)
In the KTB field laboratory, thermal conductivity was measured on cuttings material in depth intervals of 10 m and on available drill core material. The results on drill cores... -
Ultrasonic Seismics on Mini Cores (Plugs) of the KTB Main Hole HB1a
Ultrasonic wave propagation through core samples is studied in a water tank to insure good signal transmission between transducer, rock specimen and receiver and to avoid time -... -
Porosity of Mini Cores (Plugs) of the KTB Main Hole HB1d
The porosity was determined using the most common Archimedian method (Schopper, 1982). It is based on the following three weight determinations of the sample: (1) The samples... -
Vertical distribution in the sediment of the different animal groups found in...
The vertical distribution of organisms in the sediment indicates that animals can be present as deep as 15 cm although at very low abundance at such depths (Fig. 4, Fig. 5 and... -
Permeability of Mini Cores of the KTB Main Hole HB1a
In the KTB field laboratory, porosity, internal surface and permeability were determined on identical mini cores with 25.4 mm in diameter and approximately 50 mm in length.... -
Thermal Conductivity of Cores of the KTB Main Hole HB1a (measured data)
The thermal conductivity on cores is measured in two steps (see Pribnow 1994). First, one face end of the core is sawed and polished. The half space line source is pressed... -
Magnetic Susceptibility of Mini-Cores of the KTB Pilot Hole VB1a
The magnetic susceptibility is measured by an inductive AC device (BARTINGTON). The sample is placed inside a coil which generates an alternating magnetic field. The applied... -
Raw pollen data from kasten core CON01-603-5 part1 (counts)
Sediment slices of 0.5 cm thickness were obtained from gravity core segments and of 1 cm thickness from the Vydrino piston core. Volumetric subsamples of 5 cm3 (10 cm3 in case... -
Radial Vp on Core Samples of the KTB Main Hole HB1a
Ultrasonic wave propagation through core samples is studied in a water tank to insure good signal transmission between transducer, rock specimen and receiver and to avoid time -... -
Day plot data of hysteresis parameters of representative samples for VER98-1-...
The day plot (Fig. 6B; Day et al., 1977) indicates that samples with S-ratios >0.95 plot rather in the single-domain (SD) to pseudosingle-domain (PSD) range. Samples with... -
SAFOD Main Hole downhole logging data phase 2 (2005), 3799-3987m
SAFOD is motivated by the need to answer fundamental questions about the physical and chemical processes controlling faulting and earthquake generation within a major... -
Electrical Resistivity of Cores of the KTB Pilot Hole VB1
In general, four-electrode devices are used to measure the resistivity on original (unprepared) cores and on mini cores drilled from these original cores. The in-phase and the... -
Thermal Conductivity of Cuttings of the KTB Main Hole HB1h (transformed data)
In the KTB field laboratory, thermal conductivity was measured on cuttings material in depth intervals of 10 m and on available drill core material. The results on drill cores... -
Electrical Resistivity of Mini Cores (Plugs) of the KTB Main Hole HB1d
In general, four-electrode devices are used to measure the resistivity on original (unprepared) cores and on mini cores drilled from these original cores. The in-phase and the... -
Magnetic Susceptibility of Mini-Cores of the KTB Main Hole HB1i
The magnetic susceptibility is measured by an inductive AC device (BARTINGTON). The sample is placed inside a coil which generates an alternating magnetic field. The applied...