-
Electrical Resistivity of Mini Cores (Plugs) of the KTB Main Hole HB1
In general, four-electrode devices are used to measure the resistivity on original (unprepared) cores and on mini cores drilled from these original cores. The in-phase and the... -
XRF of Cuttings of the KTB pilot hole VB1
Cuttings were crushed in a tungsten carbide ball mill for 25 min; while core samples were crushed in a tungsten carbide jaw breaker and then processed in the same way as the... -
Magnetic Susceptibility of Cuttings of the KTB Pilot Hole HB1a
The magnetic susceptibility is measured by an inductive AC device (BARTINGTON). The sample is placed inside a coil which generates an alternating magnetic field. The applied... -
Geochemical Analysis of Cations of Mud Samples of the KTB Main Hole HB1h.
Geochemical Analysis of Cations of Mud Samples of the KTB Main Hole HB1h. -
XRF of Cuttings of the KTB Main Hole HB1g.
Cuttings were crushed in a tungsten carbide ball mill for 25 min; while core samples were crushed in a tungsten carbide jaw breaker and then processed in the same way as the... -
Geochemical Analysis of Cations of Mud Samples of the KTB Main Hole HB1g.
Geochemical Analysis of Cations of Mud Samples of the KTB Main Hole HB1g. -
Magnetic Susceptibility of Cuttings of the KTB Pilot Hole HB1d
The magnetic susceptibility is measured by an inductive AC device (BARTINGTON). The sample is placed inside a coil which generates an alternating magnetic field. The applied... -
Thermal Conductivity of Cuttings of the KTB Main Hole HB1i (transformed data)
In the KTB field laboratory, thermal conductivity was measured on cuttings material in depth intervals of 10 m and on available drill core material. The results on drill cores... -
Density of Core Samples of the KTB Main Hole HB1
The density of rocks depends on the mineral contents and is therefore a helpful property for the discrimination of lithological units. It is also used for the calculation of... -
XRF of Centrifuge Samples of the KTB Pilot Hole VB1a.
Cuttings were crushed in a tungsten carbide ball mill for 25 min; while core samples were crushed in a tungsten carbide jaw breaker and then processed in the same way as the... -
XRD of Cuttings of the KTB Pilot Hole VB1a
The qualitative and quantitative phase analyses were performed in the KTB field laboratory by x-ray powder diffraction using SIEMENS D 500 diffractometer. During early stages of... -
Gas Radon Measurements of Gas Samples of the KTB Main Hole HB1h
In the complete KTB-VB and in in the KTB-HB down to a depth of 3003 m the gas phase was released and collected by twirl degassers attached in front of the mud shakers. This open... -
Density of Core Samples of the KTB Pilot Hole VB1
The density of rocks depends on the mineral contents and is therefore a helpful property for the discrimination of lithological units. It is also used for the calculation of... -
Thermal Conductivity of Cuttings of the KTB Main Hole HB1g (transformed data)
In the KTB field laboratory, thermal conductivity was measured on cuttings material in depth intervals of 10 m and on available drill core material. The results on drill cores... -
Radial Vp on Core Samples of the KTB Main Hole HB1
Ultrasonic wave propagation through core samples is studied in a water tank to insure good signal transmission between transducer, rock specimen and receiver and to avoid time -... -
Electrical Resistivity of Mini Cores (Plugs) of the KTB Main Hole HB1g
In general, four-electrode devices are used to measure the resistivity on original (unprepared) cores and on mini cores drilled from these original cores. The in-phase and the... -
Thermal Conductivity of Cores of the KTB Main Hole HB1g (measured data)
The thermal conductivity on cores is measured in two steps (see Pribnow 1994). First, one face end of the core is sawed and polished. The half space line source is pressed... -
Magnetic Susceptibility of Cuttings of the KTB Pilot Hole HB1g (special samples)
The magnetic susceptibility is measured by an inductive AC device (BARTINGTON). The sample is placed inside a coil which generates an alternating magnetic field. The applied... -
XRF of Cuttings of the KTB Main Hole HB1h.
Cuttings were crushed in a tungsten carbide ball mill for 25 min; while core samples were crushed in a tungsten carbide jaw breaker and then processed in the same way as the... -
Electrical Resistivity of Cores of the KTB Main Hole HB1
In general, four-electrode devices are used to measure the resistivity on original (unprepared) cores and on mini cores drilled from these original cores. The in-phase and the...
